Duralite Regulators

Click to enlarge

• Surface mounted electronic components.
• Compact heat sink.
• Full RF filter in and out delivers highest performance.
• Rated at 7.5 amps with 10 amp spikes
• Unique Hybrid Pulsing Design
• Designed for 6 - 8.4 volts
• Specifically designed for use with the DURALITE PLUSTM Battery but also works well with other battery chemistry types.

SPECIFICATIONS & TECHNICAL INFORMATION

All Duralite Regulators are proudly manufactured in the USA.

Click to enlarge

High Current Voltage Regulator, with Heavy Duty Switch, 7.5 amp w/16ga wire, deans connectors
5.1, 5.3, 5.6, 6.0, 7.0 volt
For applications using newest "High current draw' digital servos. Regulator built w/High Current 16 ga wire & female deans connectors. Comes with deans to RX adaptor, weighs 2oz.

Click to enlarge

Voltage Regulator, 7.5 amp w/standard 22ga wire
5.1, 5.3, 5.6, 6.0, 7.0 volt
For use with aftermarket switch. Weighs .6oz (20grams)

Click to enlarge

Voltage Regulator with Fail Safe Switch, 7.5 amp w/standard 22ga wire
5.1, 5.3, 5.6, 6.0, 7.0 volt
If the switch were to fail regulator stays in the on state until you unplug it from the battery. Not suitable for ignition applications due to fail safe feature.(See #804001 Digi Switch)

Click to enlarge

Voltage Regulator with Heavy Duty Fail Safe Switch, 7.5 amp w/standard 22ga wire
5.1, 5.3, 5.6, 6.0, 7.0volt
Ideal for 3D helicopter & 3D aircraft applications. Regulator with the FUTABA* heavy duty fail safe switch. The switch itself is a multi pole design which has proven to withstand vibration better than the standard single pole switch. If the switch were to fail regulator stays in the on state until you unplug it from the battery. Not suitable for ignition applications due to fail safe feature. Weighs 1.6oz (45grams)

Voltage Regulator for DSC 7.5 w/standared 22 ga wire #54051-DSC - 5.1 volt
Ideal for use with DSC transmitter link on any aircraft, helicopter or jet. Weighs 1.6oz (45grams)

Click to enlarge

Voltage Step Down for Helicopter Tail
#55053 – .5 volt step down for use with a 6 volt regulated power supply
#55055 – 1.5 volt step down for use with a 7 volt regulated power supply
Economical, light weight option for pilots who want to use a 6 or 7 volt regulated power supply in a helicopter while not effecting the operation of the gyro. Recommended for use with FUTABA* 9241, 9251, 9253, 9254, 9255, 9256 servos.
NOTE: Item is not a regulator. Not recommended for NiCad or NiMh or A123.
Specifications: 6.75" long, Weighs .2 oz
Details & Installation

Click to enlarge

#804000 - Electronic Switch
Parallel redundant switch and regulators all in one. Ideal for smaller models and models up to 27%. Will handle up to 5 amps continuous. The switch is a fail safe type with led lights for visibility. Designed to work with any of the Duralite Plus batteries.
• Power handling up to 5.0 Amps (according to heatsink)
• Two independent linear voltage regulators, supplying 5.90 Volts
• Two independent electronic switches
• Two volt controller ( in 4 steps ) for each battery
• Two Low voltage memory for both batteries
• SET button for On / Off switching protection
• LED indicators for both power circuits
• Operating voltage range 4.0 to 9.0 Volts
• Temperature range -10° to +75° C
• Voltage loss approx. 0.35 Volts
• Weight only 35 grammes incl. all cables
INSTRUCTIONS

Click to enlarge

#804001 - Digi Switch
Light weight digital switch with built in 5.5 volt regulator. Will handle up to 5 amps load. External led will tell you the voltage of your DURALITE PLUS battery at a glance. Rugged fiber glass filled plastic case is virtually indestructible. Perfect for Pattern planes where weight is critical. Excellent for ignition applications
• Electronic switch, operated using a sensor button
• Linear IC-controlled voltage regulator
• Multi-colour LED for monitoring Li-Po battery voltage
• Low voltage detection
• Input voltage 8.40 Volts ( 2 Li- Po cells )
• Output voltage 5.50 Volts ( equates to charged 4-cell NC battery )
INSTRUCTIONS